Licensed plumbers for replacement, walk-in, and new tub installs
Bathtub Installation in Tupelo, MS Done Right the First Time
When you need bathtub installation Tupelo MS homeowners trust, we handle the whole job: removal, rough-in, drain and overflow fitting, and a watertight finish. Whether you're replacing a cracked cast-iron tub in a 1950s Mill Village bungalow or adding a walk-in unit for easier access, our licensed plumbers work to Mississippi code and test every connection before we leave. We've served Lee County for more than 25 years.
Live phone supportUpfront optionsBacked workmanship
What's included
What Our Bathtub Installation Includes
Every install covers the full job from removal to water test. Here's what's included in the price, and what we treat as an add-on if your rough-in needs extra work.
Old Tub Removal and Haul-Away
We disconnect the old tub, cut it out if it's cast iron, and haul it away. You don't rent a dumpster or pay a separate disposal fee. We protect your flooring and door frames during removal and sweep up when we're done.
Drain and Overflow Connection
We install a new drain shoe, overflow gasket, and trap arm sized to your tub. Joints are primed and cemented in PVC or ABS, then pressure-tested. We slope the drain at the required 1/4 inch per foot so water never sits in the line.
Supply Line and Valve Hookup
We connect the hot and cold supply lines to your tub filler or shower valve, using new braided lines and checking the shut-off valves. If the valve is older or corroded, we can replace it at the same visit for parts plus labor.
Leveling and Mortar Bed
We set the tub level in both directions and bed it in mortar so it doesn't flex, squeak, or crack. This is the step that separates a tub that lasts 20 years from one that fails in three. We check level again after the mortar sets.
Water Test and Cleanup
We fill the tub, let it sit, and check for any drop in the water line or moisture at the drain and overflow. We run the shower and inspect the valve connections. Then we clean up and walk you through the install before we leave.
Service overview
What Bathtub Installation Tupelo MS Really Involves
Bathtub installation Tupelo MS is the full process of removing an old tub, preparing the rough-in plumbing, setting the new unit level, and connecting the drain, overflow, and supply lines so the tub holds water and drains clean. It is not a drop-in job. We cut into the subfloor when needed, check the joists, replace a worn wax ring or corroded fittings, and pressure-test the drain before the surround goes back up. Most standard alcove tubs take four to six hours; a walk-in conversion with a tile surround can run two days.
Tupelo homes need this service for a few predictable reasons. Cast-iron tubs in older neighborhoods crack or rust through at the drain. Fiberglass units flex and spider-crack after 15 to 20 years. And a growing number of homeowners want a walk in bathtub installation Tupelo MS for a parent or for themselves. If you're searching bathtub installation near me Tupelo MS because water is pooling under the tub or the floor feels soft, that's usually a failed drain gasket, not just a cosmetic problem.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
Our Bathtub Installation Process
The process flexes to the condition, but these checkpoints keep decisions clear.
On-Site Assessment
We measure the alcove, check the existing drain and overflow location, and inspect the subfloor and joists for soft spots or past leaks. We confirm whether your rough-in matches the new tub or needs modification. You get a written price before we start. This visit takes 30 to 45 minutes and is free within Tupelo city limits.
Old Tub Removal
We shut off the water, disconnect the supply lines and drain, and cut out the old unit. Cast iron gets sectioned with a saw; acrylic and fiberglass come out in one piece. We protect your floor with drop cloths and move the old tub to our truck. Removal usually takes one to two hours depending on material and access.
Rough-In and Prep
We inspect the drain pipe, trap, and shut-off valves. Worn parts get replaced: a new wax ring, fresh supply lines, and a new drain shoe gasket. If the subfloor is soft, we sister in new plywood or replace the section. We set the new tub level on a mortar bed so it doesn't flex or squeak underfoot.
Tub Setting and Connection
We set the tub, connect the drain and overflow with PVC or ABS, and tie in the supply lines to the faucet and shower valve. Every joint gets primer and cement, then a pressure test. We check the tub for level in both directions and shim as needed. This step takes two to three hours for a standard alcove tub.
Water Test and Cleanup
We fill the tub, let it sit, and watch for any drop in the water line or moisture at the drain. We run the shower and check for leaks at the valve and supply connections. Then we clean up, haul away debris, and walk you through what we did. You get a 1-year workmanship warranty on the installation.
Tools & methods
Tools and Methods We Use for Tub Installs
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
RIDGID drain snake and auger
We clear clogged branch lines before setting a new tub, so the drain flows freely from day one. A clean line prevents backups and slow drainage.
Hydro jetting machine
For heavy buildup or grease in the drain line, we use hydro jetting to scour the pipe walls clean. This is especially useful in older Tupelo homes with cast-iron drains.
Sewer camera
We run a camera through the drain to check for root intrusion, collapsed pipe, or bellies before we connect a new tub. Finding a sewer problem early saves you from a backup later.
Pipe cutter and soldering torch
We cut and solder copper supply lines when replacing a tub valve or repairing a damaged pipe. Clean, solid joints that won't leak behind the wall.
Press fitting tool
For PEX and copper press connections, we use a press fitting tool to make fast, reliable joints without an open flame. Ideal for tight spaces behind a tub.
Leak detection equipment
We use electronic leak detection to find hidden moisture under the tub or in the subfloor before we install. Fixing the source first protects your new installation.
Use cases
When Tupelo Homeowners Call Us for Tub Work
These examples show how the service framework adapts rather than forcing every call through one repair.
Walk-In Tub Conversion in Bel Air
An elderly homeowner could no longer step over a 15-inch tub wall safely. The family worried about falls, and the existing tub had a slippery floor with no grab bars. → We removed the old tub, modified the rough-in for a deeper walk-in drain, and installed a low-threshold walk-in tub with a built-in seat and grab bars. The install took two days, and the homeowner can now bathe independently.
Fiberglass Tub Replacement in Willow Creek
A 2005 fiberglass tub had a spider crack and flexed noticeably underfoot. The homeowner worried the crack would leak into the subfloor and was avoiding using the tub. → We removed the flexing unit, set a new acrylic tub on a mortar bed, and replaced the drain and overflow. The new tub feels solid with no flex. We pressure-tested the drain and confirmed no leaks. The job took five hours.
Choose the tub
Bathtub Types We Install
There are 4 main bathtub types. Each one changes how the drain, overflow, and filler connect.
Alcove Tubs
The most common tub in Tupelo homes. Three walls surround it, and the valve and spout sit on the end wall.
Freestanding Tubs
A floor-mounted or deck filler feeds the tub, and the drain sits under the tub body.
Drop-In Tubs
The tub sits inside a framed deck. We set the drain and overflow before the deck is finished.
Walk-In Tubs
A door and a built-in seat for safer entry. Walk-in tubs need a fast-fill faucet and often a larger water heater.
Problems we solve
Bathtub Problems We Solve for Tupelo Homeowners
A failing tub rarely fails quietly. Here are the problems we see most in Tupelo, and what happens if you let them go.
Cracked or rusted cast-iron tub leaking at the drain
We cut out the old cast-iron tub, replace the rotted subfloor section, and install a new tub with a fresh drain shoe and overflow gasket. We pressure-test the drain before closing anything up, so the leak is gone for good.
Fiberglass tub flexing and spider-cracking underfoot
We remove the flexing unit and set a new tub on a mortar bed so it feels solid underfoot. We also check the subfloor for soft spots and sister in new plywood if needed. The new tub won't flex, squeak, or crack.
Slow tub drain that backs up into the shower
We run a drain snake or hydro jetting machine through the branch line before installing the new tub. If the clog is in the main sewer, we run a sewer camera to find the cause. Fixing the drain first means your new tub empties fast.
Tub drain won't hold water because the stopper is worn
We replace the drain shoe, stopper, and overflow plate during the install. If you're keeping your existing tub, we can repair just the stopper assembly. Either way, you get a drain that holds water and seals tight.
Pricing process
Bathtub Installation Cost in Tupelo
$850 - $2,400 for standard alcove replacement; $2,800+ for walk-in tubs
Tub type and material
A standard acrylic alcove tub costs less than a cast-iron or walk-in unit. Walk-in tubs with jets, heated seats, or air massage add significantly to the price. We'll quote the tub and labor separately so you see where the money goes.
Rough-in condition
If the drain location, trap arm, and supply lines match the new tub, the install is straightforward. If we need to move the drain, replace corroded shut-off valves, or adapt an older cast-iron trap, that adds labor and parts.
Subfloor condition
A soft or rotted subfloor must be repaired before the new tub goes in. We replace the damaged section with new plywood and sister in joists if needed. This is common in older Tupelo homes with past leaks.
Customer reviews
What Tupelo Homeowners Say
★★★★★
“Our 1950s cast-iron tub had rusted through at the drain and was leaking into the ceiling below. The crew cut it out, replaced the rotted subfloor section, and set a new acrylic tub in one day. They showed me the old drain pipe and explained why it failed. No more water stains on the kitchen ceiling. Worth every penny.”
★★★★★
“We needed a walk-in tub for my father, who has trouble stepping over the side. They measured the door and floor, told us exactly which model would fit, and installed it in two days. They added grab bars and a handheld wand. My dad can bathe safely again, and the price matched the quote to the dollar.”
★★★★★
“Our fiberglass tub had a spider crack and flexed every time you stepped in. They set the new tub on a mortar bed so it feels solid, replaced the drain and overflow, and tested it twice before leaving. They also hauled away the old tub and cleaned up the bathroom. I'd call them again for any plumbing work.”
How much does bathtub installation cost in Tupelo MS?
Most standard alcove tub replacements in Tupelo run $850 to $2,400 installed in 2026, including removal and haul-away. Walk-in tubs start around $2,800 and go up with features like whirlpool jets or heated seats. The biggest cost variables are tub material, whether the rough-in needs modification, and whether the subfloor is sound. We give you a written price before we start, so you know the number up front.
How long does bathtub installation take in Tupelo Mississippi?
A standard alcove tub replacement takes four to six hours from removal to final water test. Walk-in tubs and tile-surround conversions run two days because of waterproofing and finish work. If we find a rotted subfloor or a cracked drain line, add a few hours for the repair. We schedule most installs within three to five business days of your call, and same-day slots are often available.
Do you install walk in bathtubs in Tupelo?
Yes. We install walk-in tubs with low thresholds, built-in seats, and grab bars for Tupelo households. We check door swing, floor support, and drain location before you order, because a walk-in tub needs a deeper rough-in than a standard tub. We also install handheld shower wands and non-slip mats at the same visit. Most walk-in conversions take two days and start around $2,800 installed.
Can you install a bathtub I bought in Tupelo MS?
Yes, we install customer-supplied tubs. Send us the make and model before the appointment so we can confirm the rough-in dimensions match your alcove and that the drain location works. If the tub needs a different trap arm or supply line configuration, we'll tell you before the install day. We warranty our labor for one year; the tub itself carries the manufacturer's warranty.
Will a new bathtub fit through my bathroom door?
A standard 60-inch (152 cm) alcove tub fits through most interior doorways when tipped on its side. Large freestanding and walk-in tubs need measuring before purchase, and sometimes the door trim comes off.
Do I need a bigger water heater for a soaking tub?
Yes, a large soaking tub often needs a bigger water heater, since a tub over 60 gallons (227 liters) can drain a 40-gallon tank. We size the water heater to fill the tub with hot water to spare.
Related services
Related Services
Emergency Plumbing
If your old tub is leaking through the ceiling or a supply line bursts during removal, our emergency crew responds 24/7 across Tupelo. We shut off the water, stop the damage, and get your bathroom dry before we schedule the new tub install.
Residential Plumbing
Bathtub installation is one part of our residential plumbing work in Tupelo. We handle everything from a running toilet to a full bathroom remodel, so you can bundle the tub install with a new shower valve, toilet, or vanity sink and save on a single visit.
Commercial Plumbing
We install bathtubs in Tupelo rental properties, small hotels, and assisted-living facilities. Commercial tub installs need durable finishes and code-compliant grab bars. We work around tenant schedules and can stage multiple units over a few days to keep your property rentable.Ready when you are
Get Your Bathtub Installation Tupelo MS Scheduled Today
We're licensed, insured, and we've been installing tubs in Tupelo for more than 25 years. You get a written price before we start and a 1-year workmanship warranty when we finish. Call now and we'll get you on the schedule, often within the same week.
Talk with the local team
Request Bathtub Installation
Call (662) 550-8327 to reach a live dispatcher. We answer 24/7 for emergencies and book same-day appointments Monday through Friday. If you prefer email, send your address and a description of the problem to info@tupelomsplumbing.com and we will reply with an arrival window.