Licensed local plumbers, same-day installs, old units hauled away
Garbage Disposal Installation in Tupelo, MS Done Right the First Time
If your old disposal is jammed, leaking from the bottom, or humming without spinning, we handle garbage disposal installation Tupelo MS homeowners can count on. Our licensed crew installs 1/3 HP to 1 HP units, wires them to code, seals the drain flange, and pressure-tests every connection before we leave. We haul off the old unit at no extra charge and back the work with a written warranty.
Live phone supportUpfront optionsBacked workmanship
What's included
What Our Garbage Disposal Installation Covers
Every install includes the labor, hardware, and testing needed to leave you with a working disposal and a dry cabinet. We quote add-on work separately before we start, so you always know the full number.
Old Unit Removal
We disconnect the dishwasher line, drop the old disposal, and haul it away. No extra fee, no unit left at the curb. We bag it so grease and food residue do not end up on your kitchen floor.
New Mounting Hardware
Fresh sink flange, gaskets, mounting ring, and plumber's tape are included. We do not reuse old putty or corroded rings. That is the number one reason a new disposal leaks within the first month.
Drain and Trap Check
We inspect the P-trap, discharge tube, and drain opening for cracks or buildup. If the trap needs replacing, we quote it before we start. A clean drain connection is what keeps the new unit from backing up.
Wiring and Breaker Check
We confirm the disposal is on a dedicated circuit, check the breaker size, and verify the ground. If the old install was hardwired without a disconnect, we correct it to meet current code before we finish.
Full Leak Test
We run water through the disposal for a full minute and check the flange, discharge, and trap for drips. Nothing gets buttoned up until the cabinet floor is dry. You see the test before we pack up.
Warranty and Walkthrough
We show you how to run the unit, what not to put down it, and where the reset button is. You get a written workmanship warranty plus the manufacturer warranty on the disposal itself.
Service overview
Garbage Disposal Installation Tupelo MS: What the Job Really Involves
Garbage disposal installation Tupelo MS is the removal of your old grinder and the mounting, wiring, and sealing of a new unit under your kitchen sink. It is not a swap-and-go job. We cut power at the breaker, disconnect the dishwasher drain line, drop the old disposal, scrape the old plumber's putty off the sink flange, and check the P-trap and supply lines while everything is open. Then we set the new mounting assembly, tighten the three-bolt ring, reconnect the discharge tube, and run water through the chamber to confirm zero drips.
Most Tupelo calls come from two situations. Either the disposal finally died after 8 to 12 years of service, or a homeowner is upgrading to a quieter, higher-horsepower model while a plumber is already on site for a clogged drain or leaky faucet. If you are searching for garbage disposal installation near me Tupelo MS, we cover the whole city and Lee County, usually with same day garbage disposal installation Tupelo appointments available when you call before noon.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
What to Expect on Install Day
The process flexes to the condition, but these checkpoints keep decisions clear.
Phone Intake
Call (662) 550-8327 and tell us what is happening: leaking, jammed, dead, or upgrading. We ask for your sink type, cabinet clearance, and whether you have a dishwasher tied in. That lets us load the right mounting hardware and a disposal sized for your setup before we roll.
On-Site Inspection
We pull the breaker, open the cabinet, and inspect the existing flange, P-trap, and wiring. If the P-trap is cracked or the shut-off valves are seized, we tell you before we start and quote the add-on. No surprise line items when the job is done.
Removal and Prep
We disconnect the dishwasher drain hose, remove the old disposal, and scrape the sink flange clean. The old unit goes into a bucket, not on your kitchen floor. We check the drain opening for corrosion and clean the threads so the new mounting ring seats flat.
New Unit Install
We set the new flange with fresh plumber's tape and putty, mount the disposal, reconnect the discharge tube and dishwasher line, and wire the unit to the dedicated circuit. Every connection gets tightened with a pipe wrench and checked by hand before power comes back on.
Test and Walkthrough
We run the disposal with water for a full minute, check for leaks at the flange, discharge, and trap, and confirm the reset button works. Then we show you what not to put down it and leave the old unit in our truck. You get a written warranty before we pull out of the driveway.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
RIDGID Pipe Wrench
Used to break loose the mounting ring and drain fittings without stripping the threads. We carry two sizes on every truck so we are not forcing a fitting that should come off clean.
Milwaukee Cordless Drill
Drives the mounting screws and handles the wiring connections when we hardwire a unit. Cordless means no extension cord running across your kitchen floor.
Drain Snake and Auger
Clears food and grease buildup in the P-trap and branch line before the new disposal goes on. We run it through the drain opening so we are not pulling the trap unnecessarily.
Sewer Camera
Scopes the drain line when backups keep happening after a new install. It shows us root intrusion, bellied pipe, or scale buildup so we fix the real problem.
Leak Detection Equipment
Confirms whether a leak is coming from the disposal, the supply line, or the shut-off valve. That keeps you from paying for a new unit when the real leak is a $15 valve.
Pipe Cutter and Press Fitting Tool
Cuts and reconnects copper or PEX piping when the drain stub-out or supply line needs replacing during the install. Press fittings mean no open flame under your cabinet.
Use cases
When to Schedule a Disposal Install
These examples show how the service framework adapts rather than forcing every call through one repair.
Jammed Unit in Bel Air
The disposal hummed but would not spin. The homeowner had already tried the reset button and a plunger with no luck. The unit was 8 years old and still in good shape otherwise. → We pulled the unit, cleared a jammed piece of bone from the flywheel, and tested the motor. It ran clean, so the homeowner kept the unit and saved the cost of a replacement. The whole visit took 40 minutes.
New Sink and Disposal in Willow Creek
A homeowner was replacing a drop-in sink with an undermount and wanted a quieter disposal. The old unit was a builders-grade 1/3 HP model that rattled the whole cabinet. → We set the new undermount sink, sealed the drain, and installed a 1 HP unit with sound insulation. The kitchen was noticeably quieter and the drain connection was leak-tested before we left. One visit covered both jobs.
Pick the size
Garbage Disposal Sizes and Who Each One Fits
Garbage disposals come in 4 motor sizes. Household size and cooking habits decide the right horsepower (HP).
1/3 HP
Light use for 1 to 2 people. Lowest cost, louder, and more prone to jams.
1/2 HP
Daily use for 2 to 4 people. The most common size in Tupelo kitchens.
3/4 HP
Heavy use for 4 or more people. Grinds finer, runs quieter, and jams less.
1 HP
Large families and frequent cooks. Handles tougher scraps and most septic-safe models.
Problems we solve
Disposal Problems We Fix in Tupelo Kitchens
Most disposal calls fall into a handful of categories. Here is what we see most often and how we handle it.
Disposal leaking from the bottom housing
A bottom-housing leak means the internal seal is gone. We replace the unit, reseal the sink flange with fresh putty, and check the supply lines and shut-off valves for corrosion while we are under there. Most jobs are done in under two hours.
Unit hums but will not spin
We pull the unit, clear the jam, and test the flywheel. If the motor is still good, we reset it and you save the cost of a new disposal. If it is burned out, we install a new one on the same visit.
Repeated drain backups after install
We run a drain snake or hydro jetting machine through the branch line and P-trap to clear grease and food buildup. If the line is old cast iron or clay, we scope it with a sewer camera to check for root intrusion or a bellied pipe.
Disposal trips the breaker on startup
We check the breaker size, inspect the wiring and connections, and confirm the unit is on a dedicated circuit. If the circuit is undersized or the wiring is damaged, we correct it to meet code before the disposal goes back into service.
Pricing process
Garbage Disposal Installation Pricing
$180 - $450 for labor and hardware, plus $90 - $250 for the disposal itself
Disposal horsepower and brand
A 1/3 HP builders-grade unit costs less than a 1 HP model from Moen or Kohler. Higher horsepower means quieter operation, better grinding, and a longer lifespan. We stock common sizes on the truck so you are not waiting on a parts order.
Wiring and circuit condition
If the disposal is on a shared or undersized circuit, we correct it to code. That adds labor and possibly a new breaker. Most homes already have a dedicated circuit, but older Tupelo homes sometimes do not.
Drain and trap condition
A cracked P-trap or corroded drain stub-out needs replacing before the new unit goes on. That is usually a $40 to $120 add-on. We quote it before we start, not after.
Customer reviews
What Tupelo Customers Say
★★★★★
“Our disposal started leaking from the bottom on a Friday. I called at 9 a.m. and they had a tech out by 1 p.m. with a 3/4 HP unit on the truck. He pulled the old one, cleaned the flange, and had it running in about an hour. Took the old unit with him. Price was exactly what he quoted on the phone.”
★★★★★
“We bought a disposal at a big box store and needed it installed. TupelomsPlumbing.com came out, checked the box, and told us the mounting ring was missing. They had a replacement on the truck and installed it the same visit. No extra trip, no drama. I will use them again for the water heater.”
★★★★★
“I manage four rental houses in Tupelo and have used these guys for disposal replacements at three of them. They show up when they say, the work is clean, and they do not leave a mess in the cabinet. The written warranty matters to me because tenants are hard on disposals.”
Questions before we arrive
Frequently Asked Questions About Garbage Disposal Installation
How much does garbage disposal installation cost in Tupelo MS?
Most jobs run $180 to $450 in 2026, including labor, new mounting hardware, and haul-away of the old unit. The disposal itself adds $90 to $250 depending on horsepower and brand. Hardwiring a new circuit, replacing a cracked P-trap, or swapping seized shut-off valves adds to the total. We quote the full job before we start.
How long does garbage disposal installation take in Tupelo Mississippi?
A standard swap takes 45 to 90 minutes. If we are running a new dedicated circuit, replacing the P-trap, or correcting wiring from a previous install, plan on two to three hours. We block two hours for every appointment so we are not rushing the leak test at the end.
Do you haul away my old garbage disposal in Tupelo?
Yes. We remove the old unit, bag it, and take it with us on every install. There is no extra fee and you do not need to leave it at the curb. If you want to keep the old unit for a warranty claim, tell us and we will leave it in the box for you.
Can you install a garbage disposal I bought in Tupelo?
Yes, we install customer-supplied units. We check the box before we start to confirm the model, horsepower, and mounting style match your sink. If the flange or mounting ring is missing, we have replacements on the truck. Labor pricing is the same whether you buy the unit or we supply it.
Can I have a garbage disposal with a septic tank?
Yes, a garbage disposal works with a septic tank when the tank is sized for it and pumped more often. Septic-rated disposals inject enzymes that help break down food waste in the tank.
What is the difference between continuous feed and batch feed disposals?
A continuous feed disposal runs from a wall switch while you add scraps, and a batch feed disposal runs only with the stopper locked in place. Batch feed models suit homes with small children.
Related services
Other Plumbing Work We Handle in Tupelo
Emergency Plumbing
A disposal that shorts out and trips the breaker at 9 p.m. is an emergency call for us. We run 24/7 emergency plumbing across Tupelo and can isolate the circuit, pull the unit, and get your kitchen safe the same night.
Residential Plumbing
Disposal installs are part of our residential plumbing work. If your kitchen needs a new sink, faucet, or supply lines at the same time, we handle it all in one visit instead of sending two trucks on two different days.
Commercial Plumbing
We install heavy-duty disposals in Tupelo restaurants, break rooms, and commercial kitchens. These units run 1 HP and up and need dedicated circuits and larger drain lines, which we size and install to code.Ready when you are
Book Your Garbage Disposal Installation Tupelo MS Today
Call (662) 550-8327 and we will quote your install over the phone, confirm a same-day window if one is open, and bring the right unit and hardware on the first trip. Licensed, insured, and warrantied work from a crew that has been under Tupelo sinks for more than 25 years.
Talk with the local team
Request Garbage Disposal Installation
Call (662) 550-8327 to reach a live dispatcher. We answer 24/7 for emergencies and book same-day appointments Monday through Friday. If you prefer email, send your address and a description of the problem to info@tupelomsplumbing.com and we will reply with an arrival window.