Licensed plumbers for new showers, walk-ins, and full replacements
Shower Installation in Tupelo, MS Done Right the First Time
If you're searching for shower installation Tupelo MS, you want a crew that shows up on time, protects your floors, and leaves you with a shower that drains right and looks sharp. We handle new shower installation Tupelo MS for homeowners across Lee County, from simple pan-and-valve swaps to full walk-in conversions. Call (662) 550-8327 and we'll give you a straight answer on scope, price, and timeline.
Live phone supportUpfront optionsBacked workmanship
What's included
What our shower installation includes
Every shower installation includes the labor, materials, and testing needed to leave you with a working, code-compliant shower. Here's what's covered in a standard job, and what we quote separately if your situation calls for it.
Removal and disposal
We cut out the old pan, surround, valve, and drain assembly, then haul everything off. Floor protection goes down before demo starts. If the old unit is cast iron, we handle the extra weight and disposal fees.
New drain and pan
A new drain assembly and pan get set with the correct slope so water moves to the drain. We flood-test the pan for 15 minutes before closing the wall. This is where most cheap installations fail, and it's the part we don't rush.
Valve and supply lines
We install a new pressure-balancing or thermostatic valve and replace the supply lines with PEX or copper. Old galvanized lines get swapped out so you have full pressure and no hidden corrosion behind the wall.
Surround or tile finish
Acrylic and solid-surface surrounds go up in a few hours. Tile work takes longer because of drying time, but we set it level and caulk the seams with silicone so you're not re-caulking every spring.
Testing and walkthrough
We test the valve at full pressure, check for leaks at every joint, and flood-test the pan. Then we walk you through the operation and hand you the warranty. You'll know how everything works before we leave.
Service overview
Shower installation Tupelo MS: what the job actually involves
Shower installation Tupelo MS means removing the old pan, valve, and surround, then rebuilding the wet area so it drains correctly and meets Mississippi plumbing code. We cut out the old drain assembly, check the subfloor for soft spots, set a new pan or tile base with the right slope, and rough in a pressure-balancing or thermostatic valve. Supply lines get replaced with PEX or copper, and every joint gets tested before the wall goes back up.
Most calls we get in Tupelo start with a cracked fiberglass pan, a valve that won't hold temperature, or a tub the homeowner wants gone. Older homes around Mill Village and Thomas Street often have cast iron drains and undersized supply lines, so a shower replacement Tupelo job there means upgrading more than just the fixture. If you've been typing shower installation near me Tupelo MS into your phone, we cover the whole job, not just the pretty part.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
Our shower installation process, step by step
The process flexes to the condition, but these checkpoints keep decisions clear.
On-site assessment
We measure the alcove, check the drain size and location, and look at the valve and supply lines. You get a written price before we start. Takes 30 to 45 minutes, and there's no charge for the estimate.
Demo and prep
We shut off the water, cut out the old pan and surround, and haul it off. Floor protection goes down first. If the subfloor is soft, we sister in new framing before anything else. Usually two to three hours.
Rough-in and valve work
New PEX or copper supply lines, a new drain assembly, and a code-correct valve get installed and tested. We check for square and level because a pan that's off by a quarter inch will pool water at one corner.
Pan, surround, and finish
The new pan gets set in mortar or adhesive, the surround or tile goes up, and we caulk the seams with silicone. We flood-test the pan for 15 minutes before we call it done. This is the longest part of the day.
Cleanup and walkthrough
We haul off every scrap, wipe down the fixtures, and walk you through the valve operation and any maintenance. You get a workmanship warranty and our number if anything looks off. We're out the door with the bathroom ready to use.
Tools & methods
Tools and methods we use on shower installs
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Pipe wrench and press fitting tool
Used to break loose old supply lines and make clean connections on new copper or PEX without a torch in tight wall cavities.
Soldering torch and pipe cutter
For copper supply lines where a soldered joint is the right call. The pipe cutter gives a square cut so the joint seals on the first try.
Drain snake and sewer camera
We run a snake through the branch line before setting a new pan, and we camera the line if the drain is slow or the home is older.
Hydro jetting machine
Used when demo debris or years of soap scum have narrowed the drain line. It clears the pipe back to bare walls so the new shower drains fast.
Leak detection equipment
When a shower leak shows up on the ceiling below, we use it to pinpoint the source without tearing out the entire surround.
Level, square, and flood-test kit
A pan that's off by a quarter inch pools water at one corner. We check level and square, then flood-test the pan for 15 minutes before closing the wall.
Use cases
When Tupelo homeowners call us for showers
These examples show how the service framework adapts rather than forcing every call through one repair.
Tub-to-walk-in conversion in Park Heights
A homeowner wanted to remove a cast iron tub and install a walk-in shower for an aging parent. The tub drain didn't line up with the new pan, and the walls had no blocking for grab bars. → We cut out the tub, relocated the drain and trap, blocked the walls, and installed a low-threshold pan with a bench. The job took two days, and the shower passed inspection with no corrections.
One-day rental turnover near Downtown Tupelo
A rental unit had a stained, cracked surround and a valve that leaked behind the wall. The landlord needed the unit rent-ready in 48 hours and couldn't afford a multi-day vacancy. → We pulled the permit, installed a new pan, surround, and valve in one day, and had the unit ready for the inspector the next morning. The tenant moved in that weekend.
Plan the shower
Shower Installation Options for Tupelo Homes
There are 4 common shower projects in Tupelo homes. The plumbing work differs for each one, mainly at the drain and the valve.
Tub-to-Shower Conversion
We remove the tub, move the drain to the new pan location, and raise the valve and shower arm to shower height.
Walk-In and Curbless Showers
A curbless shower needs the subfloor recessed and a linear or sloped drain so water stays in the wet area.
Prefab Shower Kits
Fiberglass and acrylic units install in 1 day with a matching pan, drain, and valve.
Custom Tile Showers
We rough in the valve and drain, then the tile contractor builds the waterproofed pan and walls.
Problems we solve
Shower problems we fix for Tupelo homeowners
Most shower calls start with one of these four problems. We diagnose the cause, not just the symptom, so you're not paying for the same repair twice.
Cracked pan leaking into the ceiling below
We cut out the failed pan, inspect the subfloor for rot, and install a new pan with a proper slope and drain seal. We flood-test it before closing the wall so you know the leak is fixed.
Valve that won't hold temperature
We replace the valve with a new pressure-balancing or thermostatic unit that holds within 2 degrees. If the valve body is fine, we swap the cartridge and save you the cost of a full replacement.
Tub-to-shower conversion with drain mismatch
We relocate the drain and trap to match the new pan, then tie it into the existing branch line. We camera the line first to make sure it's clear and sized correctly for the new fixture.
Low water pressure at the shower head
We test pressure at the valve, check the supply lines, and replace any galvanized pipe with PEX or copper. If the issue is scale, we clean the cartridge and shower head and restore full flow.
Pricing process
What shower installation costs in Tupelo
$1,200 - $4,500 depending on scope
Pan and surround material
Acrylic and fiberglass kits are the most affordable and install in a day. Solid-surface and tile cost more because of material and labor time. Tile adds two to three days for drying and grouting.
Valve type and brand
A basic pressure-balancing valve from Moen or Delta costs less than a thermostatic valve from Kohler. Thermostatic valves hold temperature more precisely, which matters in homes with multiple bathrooms.
Drain relocation
If the new pan doesn't line up with the old drain, we cut the slab or subfloor and move the trap. That adds labor and sometimes concrete work. It's common in tub-to-shower conversions.
Customer reviews
What Tupelo homeowners say
★★★★★
“Our fiberglass pan cracked and water was dripping into the kitchen. TupelomsPlumbing.com came out the next morning, showed us the rotten subfloor, and quoted the repair on the spot. They had the new pan and surround in by 4 p.m. that day. No more leak, and the price matched the quote exactly.”
★★★★★
“We wanted a walk-in shower for my mother, who's 78. The crew cut the curb down, blocked the walls for grab bars, and sloped the pan so it drains fast. They were careful with the tile and cleaned up every bit of dust. It took two days, just like they said.”
★★★★★
“I manage three rental units near Downtown Tupelo and needed a shower replacement Tupelo job done between tenants. They gave me a same-day estimate, pulled the permit, and finished in one day. The inspector passed it without a single correction. I've used them on two more units since.”
How much does shower installation cost in Tupelo MS?
Most standard shower replacements in Tupelo run $1,800 to $4,500 in 2026, including the pan, surround, valve, and labor. A simple pan-and-valve swap on an existing base can land closer to $1,200. Custom tile, bench seats, and moving the drain push it higher. We give you a written price before demo starts.
How long does shower installation take in Tupelo Mississippi?
A standard acrylic or fiberglass replacement takes one day, usually six to eight hours. Tile showers and custom pans run two to four days because of drying time between coats. If we find soft subfloor or need to move the drain, add a day. We tell you the timeline at the estimate, not the morning of.
Do you install walk in showers in Tupelo?
Yes. Walk in shower installation Tupelo MS is one of our most common jobs, especially for homeowners planning to stay in the house long term. We cut the curb down to a low threshold, block the walls for future grab bars, and slope the pan so water moves to the drain without pooling. Most walk-in conversions take one to two days.
Can you install a shower I bought in Tupelo MS?
Yes, we install customer-supplied showers as long as the unit matches your alcove dimensions and the drain location lines up. Send us the model number and a photo of the space before the appointment. If the pan won't fit or the valve is the wrong rough-in depth, we'll tell you before we start cutting.
What is a pressure-balancing shower valve?
A pressure-balancing shower valve keeps water temperature steady when another fixture changes the hot or cold pressure. Plumbing codes require an anti-scald valve on new shower installations.
Do I need a permit for a tub-to-shower conversion?
Yes, a tub-to-shower conversion that moves the drain or valve needs a plumbing permit in most of Tupelo and Lee County. We pull it and schedule the inspection before the walls close.
Related services
Related Services
Emergency Plumbing
A shower valve that blows a supply line at 2 a.m. is an emergency. We shut off the water, stop the damage, and come back to finish the shower installation Tupelo MS work once the mess is under control.
Residential Plumbing
Shower installation is part of the broader residential plumbing work we do across Tupelo. If your bathroom has other issues, like a slow sink drain or a running toilet, we can handle it on the same visit and save you a trip charge.
Commercial Plumbing
We install showers in small commercial settings too, like gyms, barber shops, and rental units around Downtown Tupelo. Commercial jobs need backflow prevention and sometimes a different valve spec, so we quote them separately from residential work.Ready when you are
Get your shower installation Tupelo MS quote today
We're licensed, insured, and we've been installing showers in Tupelo for more than 25 years. Call (662) 550-8327 and we'll schedule a free on-site estimate. If your old shower is leaking, tell us and we'll prioritize the call.
Talk with the local team
Request Shower Installation
Call (662) 550-8327 to reach a live dispatcher. We answer 24/7 for emergencies and book same-day appointments Monday through Friday. If you prefer email, send your address and a description of the problem to info@tupelomsplumbing.com and we will reply with an arrival window.