Kitchen and bathroom sinks set, sealed, and leak-tested
Sink Installation in Tupelo, MS Done Right the First Time
If you need sink installation Tupelo MS homeowners can count on, we set kitchen and bath sinks the right way: new shut-off valves, fresh supply lines, a clean cutout, and a drain that holds water without a drip. Whether you bought a farmhouse basin for a Mill Village kitchen or a vanity top for a bathroom in Bel Air, we handle the plumbing side so you are not fighting a leaking basket strainer at 9 p.m. Same-day slots are often open.
Live phone supportUpfront optionsBacked workmanship
What's included
What our sink installation includes
Every sink job we run in Tupelo includes the labor to remove the old fixture, set the new one, and reconnect the water and drain. We also replace the shut-off valves and supply lines as part of the standard price. Add-ons like a new faucet, disposal, or countertop cutting are quoted separately so you know what you are paying for.
Old sink removal
We disconnect the supply lines and drain, cut the old sealant, and lift the old basin out. The countertop gets scraped clean so the new rim sits flat. We haul the old sink away unless you want to keep it for a shop or garage.
New shut-off valves
Every sink install gets new quarter-turn shut-off valves. Old gate valves seize and leak when you turn them. New valves cost a few dollars each and mean you can shut the water off at the fixture without running for the main.
Braided supply lines
We replace the flexible supply lines with new braided stainless lines sized to the fixture. Old plastic or rubber lines crack with age and are a common source of cabinet leaks. New lines are rated for the pressure and come with a warranty.
Drain and trap hookup
The basket strainer or pop-up assembly goes in with a fresh gasket. We cut the tailpiece to length and set the P-trap at the correct depth, then connect to the trap arm with the right slope. If the old trap was an S-trap or accordion flex pipe, we replace it with smooth-wall pipe.
Full leak test
Before we leave, we fill the basin, pull the stopper, and watch the drain run. We run hot water for two minutes and check every joint with a dry paper towel. If anything weeps, we fix it on the spot. You get a walkthrough of the shut-off valves and the disposal reset button.
Service overview
What sink installation Tupelo MS really involves
Sink installation Tupelo MS is the licensed trade work of removing an old basin or setting a new one, then reconnecting the water supply and drain so the fixture drains fast and stays dry. That means cutting or adjusting the countertop opening, mounting the sink, sealing the rim, installing a basket strainer or pop-up assembly, and tying into the trap arm. We also swap the shut-off valves and supply lines while the cabinet is open, because old angle stops are the number one cause of a slow drip after a new sink goes in.
Most calls we run in Tupelo start the same way. A homeowner buys a sink online, then finds the old drain line does not line up, the disposal flange is seized, or the countertop cutout is 1/4 inch too small. Others are dealing with a leaky faucet that finally soaked the cabinet floor. If you have been typing sink installation near me Tupelo MS into your phone, we carry the pipe cutter, wax ring, plumber's tape, and fittings to finish the job in one visit instead of three.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our sink installation process works
The process flexes to the condition, but these checkpoints keep decisions clear.
Phone intake
You call (662) 550-8327 and tell us what you bought or what is failing. We ask the sink type, the countertop material, and whether there is a disposal. That takes about five minutes and lets us load the right fittings, a disposal flange kit, and the correct strainer size before we leave the shop. You get a window, not a vague all-day promise.
Shut-off and removal
We shut the water at the angle stops or the main, then disconnect the supply lines and drain. The old sink comes out, and we scrape the old plumber's putty and silicone off the countertop. If the cutout needs trimming, we do it with a jigsaw and a template so the new rim sits flat. Removal usually takes 20 to 40 minutes.
Fit and seal
We dry-fit the new basin, check the rim overhang, then set it in a bead of silicone or plumber's putty. Undermount sinks get the mounting clips torqued in sequence so the rim pulls down evenly. The basket strainer or pop-up assembly goes in with a fresh gasket. This is the step that decides whether the sink leaks in year one or year ten.
Supply and drain hookup
New quarter-turn shut-off valves and braided supply lines go in. We cut the tailpiece to length, set the P-trap at the right depth, and connect to the trap arm with the correct slope. If there is a disposal, we mount the flange, set the snap ring, and wire it to a switched outlet. Hookup takes 30 to 50 minutes.
Test and walkthrough
We fill the basin, pull the stopper, and watch the drain run. Then we run hot water for two minutes and check every joint with a dry paper towel. You get a walkthrough of the shut-off valves and the disposal reset button. If anything weeps, we fix it before we leave, not on a return trip.
Tools & methods
Tools and methods we use on sink jobs
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Pipe wrench
Used to break loose old drain nuts and trap arms that have been in place for decades. A proper pipe wrench bites without crushing the pipe, which matters when you are reusing a trap arm.
Drain snake
Clears the branch line before we set a new sink. Running a snake first means the new drain does not back up on day one. We use a hand snake for short clogs and a powered auger for longer runs.
Hydro jetting machine
For grease and scale buildup in kitchen lines, a hydro jetting machine scours the pipe wall clean. We use it when a snake clears the clog but leaves residue that will catch debris again.
Pipe cutter
Cuts copper and PEX piping square so the new stub-out and tailpiece fit without burrs. A square cut is what lets a compression fitting seal on the first try.
Soldering torch
Used when we need to sweat a copper joint on a supply line or stub-out. We keep the flame away from the cabinet and use a heat shield so the wood does not scorch.
Press fitting tool
For copper and PEX connections where a torch is not safe, a press fitting tool crimps the joint in seconds. It is the tool we reach for inside a finished cabinet.
Sewer camera
When a sink backs up repeatedly, we run a sewer camera down the line to see if the problem is root intrusion or a collapsed pipe. The camera tells us whether we are clearing a clog or quoting a sewer repair.
Use cases
When Tupelo homeowners call for sink installation
These examples show how the service framework adapts rather than forcing every call through one repair.
Farmhouse sink cutout in a Mill Village remodel
A homeowner in Mill Village bought a farmhouse sink online for a kitchen remodel. The existing countertop had a standard drop-in cutout that was too small, and the old galvanized stub-outs were corroded. Two other plumbers told them to call a countertop company first. → We templated the sink, cut the countertop with a jigsaw, and set the basin with mounting clips and silicone. The galvanized stub-outs were replaced with PEX piping and new quarter-turn valves. The sink sat flush and the drain ran fast on the first test.
Bathroom vanity swap in Bel Air
A homeowner in Bel Air replaced a bathroom vanity and could not get the new sink to stop leaking at the drain. The old pop-up assembly was corroded and the wall stub-out did not line up with the new vanity's drain location. Water was dripping into the vanity cabinet. → We replaced the pop-up assembly, extended the trap arm to meet the new drain location, and set the sink with a fresh gasket. New braided supply lines and quarter-turn valves went in at the same time. The leak test held with a full basin, and the cabinet stayed dry.
Choose the sink
Sink Types We Install in Tupelo
There are 5 main sink types, and each one mounts and drains differently.
Undermount Sinks
Clipped and sealed under a stone countertop. The counter fabricator cuts the opening to the sink template.
Drop-In Sinks
The rim sits on top of the counter, which makes drop-in sinks the easiest swap on laminate.
Farmhouse Sinks
A deep apron-front sink that needs a reinforced cabinet base to carry the weight.
Vessel Sinks
Sits on top of the vanity and needs a tall faucet or a wall-mount spout.
Pedestal and Wall-Mount Sinks
Exposed drains and supply lines need clean chrome trim and a solid wall blocking.
Problems we solve
Sink problems we fix in Tupelo homes
Most sink calls are not really about the sink. They are about a failed valve, a clogged drain, or a seal that gave out years ago. Here are the problems we see most in Tupelo and how we solve them.
Leaking basket strainer soaking the cabinet floor
We pull the strainer, clean the mating surface, and reinstall it with plumber's tape and a new gasket. If the strainer body is cracked, we replace it. Then we fill the basin and watch the drain to confirm the seal holds under a full load of water.
Seized shut-off valve that will not close
We replace old gate valves with quarter-turn ball valves on every sink job. They turn with a quarter turn and do not seize. If your valves are original to the house, this is the cheapest insurance you can buy while the cabinet is already open.
Sink drains slowly or backs up into the other basin
We run a drain snake or hydro jetting machine through the branch line before we set the new sink. Clearing the clog first means the new sink drains fast from day one. If the camera shows root intrusion or a collapsed line, we quote the sewer repair before we proceed.
Disposal hums but will not turn
We free the flywheel with an auger from the bottom, check the reset button, and test the motor. If the windings are burned, we swap the disposal during the same visit. We also check the dishwasher line and the drain flange while the disposal is off.
Pricing process
What sink installation costs in Tupelo
$185 - $650 depending on sink type, parts, and drain condition
Sink type and cutout
A drop-in sink that matches the existing cutout is the fastest job. An undermount or farmhouse sink may need countertop cutting, mounting clips, or a new cabinet support. That extra labor is the biggest swing in the price.
Valve and line condition
If the old shut-off valves turn freely and the supply lines are in good shape, the job is quicker. Seized valves and corroded stub-outs add time because we have to cut and replace pipe before we can connect the new sink.
Disposal and dishwasher
Adding a disposal means mounting a flange, wiring a switched outlet, and connecting the dishwasher line. That adds roughly an hour of labor and the cost of the disposal if you need a new one.
Customer reviews
What Tupelo customers say about our sink work
★★★★★
“We bought a farmhouse sink online and could not find anyone to cut the countertop. TupelomsPlumbing.com came out, trimmed the cutout, set the sink, and replaced both shut-off valves. They tested it with a full basin of water and it has not dripped once. That was six months ago. The price was what they quoted on the phone.”
★★★★★
“I manage four rentals and needed a bathroom sink installation Tupelo MS fast because a tenant was moving in. They had a same-day slot and finished in about two hours. New faucet, new supply lines, new P-trap. The tenant moved in that evening and I have not had a callback. I use them for all my units now.”
★★★★★
“Our kitchen sink had been backing up for weeks. They ran a drain snake first, found the clog was past the trap, and cleared it before installing the new sink. If they had just set the sink, it would have backed up again. Honest work, and they cleaned up the cabinet better than it was before.”
How much does sink installation cost in Tupelo MS?
Most sink swaps in Tupelo run $185 to $450 in 2026, and a full kitchen sink installation Tupelo MS job with a new disposal and faucet can reach $650. The price depends on whether we are dropping in a new basin or cutting a countertop, whether the old valves and drain need replacing, and whether you have a disposal. We quote the job before we start, and the quote includes new shut-off valves and supply lines.
How long does sink installation take in Tupelo Mississippi?
A standard drop-in or undermount swap takes two to four hours. That covers removal, cutout fitting, sealing, new supply lines, drain hookup, and a full leak test. If we are cutting a countertop for a farmhouse sink or running new drain lines, plan on a full day. Bathroom sink installation Tupelo jobs are usually on the shorter end, around two hours, because there is no disposal to wire.
Can you install a sink I bought in Tupelo?
Yes. We install customer-supplied sinks every week, from Moen and Delta basins bought at a Tupelo hardware store to Kohler farmhouse sinks ordered online. Have the model number and the cutout template ready when you call. We check the drain location and the strainer size before we arrive so we bring the right parts. If the sink arrives damaged or the cutout is wrong, we tell you before we start cutting.
Do you install kitchen sinks in Tupelo MS?
We install kitchen and bathroom sinks, and we handle the whole hookup: shut-off valves, supply lines, basket strainer, P-trap, and disposal if you have one. Kitchen sink installation Tupelo jobs are our most common call, followed by bathroom vanity swaps. We also do sink replacement Tupelo work when an old cast-iron basin has cracked or the drain has rusted through.
Can a new sink use my existing faucet?
Yes, a new sink can use the existing faucet when the hole count and spacing match. Undermount sinks need the faucet holes drilled in the countertop instead of the sink.
Do you connect the garbage disposal and dishwasher?
Yes, we connect the garbage disposal and dishwasher drain as part of a kitchen sink installation. The dishwasher drain gets a high loop or air gap to keep dirty water out of the dishwasher.
Related services
Other plumbing work we handle in Tupelo
Emergency Plumbing
A sink supply line that lets go at 2 a.m. is an emergency. We answer the phone around the clock and can shut off the water, replace the failed line, and get the sink back in service. Same crew that does our sink work, so you are not explaining the setup twice.
Residential Plumbing
Sink installation is part of the residential plumbing work we do across Tupelo. If the same visit turns up a running toilet or a leaky faucet, we fix it while we are there. One trip, one invoice, and your kitchen and bath are both back in shape.
Commercial Plumbing
Restaurants and offices in Downtown Tupelo need hand sinks and prep sinks that pass health inspection. We install commercial basins, grease trap connections, and backflow prevention on the supply side. We work after hours so your kitchen does not lose a service day.Ready when you are
Get your sink installation Tupelo MS scheduled today
Call (662) 550-8327 and tell us what you bought or what is leaking. We quote the job before we start, carry the parts on the truck, and test every connection before we leave. Same-day slots are often open, and we serve all of Lee County.
Talk with the local team
Request Sink Installation
Call (662) 550-8327 to reach a live dispatcher. We answer 24/7 for emergencies and book same-day appointments Monday through Friday. If you prefer email, send your address and a description of the problem to info@tupelomsplumbing.com and we will reply with an arrival window.